ZoophostDocs

Mail client settings

IMAP, SMTP and webmail settings for Outlook, Thunderbird, Apple Mail, iOS and Android, using the values from your console.

Email3 min read

Every mailbox works with standard mail clients. The console shows the exact hostnames and ports under Email → Mail settings.

Settings at a glance

Setting Value
Webmail The URL shown in the console (typically https://webmail.webspeed.online)
Incoming mail (MX target) mx.webspeed.online
Mail clients (IMAP/SMTP host) mail.webspeed.online
IMAP Port 993, SSL/TLS
SMTP submission Port 465, SSL/TLS

Always confirm against the console. If a setting there differs from this page, the console is correct for your account.

Do not use port 25 for submission. It is for server-to-server mail, is often blocked by ISPs, and requires no authentication in the wrong configuration.

Some clients label ports differently:

  • 993 — “SSL/TLS” for incoming.
  • 465 — “SSL/TLS” for outgoing (implicit TLS).
  • 587 — STARTTLS. Where supported it works, but 465 is the primary submission port on this platform; if 587 fails, use 465.

Username

The username is the full email address, for example [email protected]. This trips people up: entering only hello usually fails authentication.

Outlook (Windows)

  1. File → Add Account.
  2. Enter the email address and choose Advanced options → Let me set up my account manually.
  3. Account type: IMAP.
  4. Incoming: mail.webspeed.online, port 993, SSL/TLS.
  5. Outgoing: mail.webspeed.online, port 465, SSL/TLS.
  6. Username: the full address. Password: the mailbox password.
  7. Finish and send a test message.

Thunderbird

Thunderbird auto-detects settings from DNS. If detection fails:

  1. Account Settings → Server Settings — IMAP, mail.webspeed.online, 993, SSL/TLS, normal password.
  2. Outgoing Server (SMTP) — mail.webspeed.online, 465, SSL/TLS, normal password.
  3. Username is the full address.

Apple Mail (macOS and iOS)

  1. Mail → Add Account → Other Mail Account.
  2. Enter name, email and password. Let it fail, then fill in manually.
  3. Incoming: IMAP, mail.webspeed.online, 993, TLS.
  4. Outgoing: mail.webspeed.online, 465, TLS.
  5. Use the full address as the username.

On iOS: Settings → Mail → Accounts → Add Account → Other → Add Mail Account, then the same values under Advanced.

Webmail

Use Open webmail on the mailbox row, or the URL from Mail settings. Sign in with the full address and the mailbox password.

Webmail specifics worth knowing:

  • 20 MB attachment limit by default.
  • Remote images in HTML mail are blocked until you choose to load them.
  • Sessions end after 12 hours idle or 7 days absolute. A platform redeploy signs everyone out.
  • Mail is read over JMAP; sending goes through the relay. There is no POP access.

Troubleshooting

“Authentication failed” — use the full email address as the username, and confirm the password in the console by resetting it. Special characters in a generated password can confuse some clients; reset and paste carefully.

“Cannot connect to server” — the hostname or port is wrong, or a corporate network blocks the port. Try a mobile hotspot to isolate the network.

Mail arrives but cannot be sent — outgoing authentication is missing or the mailbox hit its daily allowance. Check both.

Certificate error — the client is using the wrong hostname (for example a proxy) or an old certificate. Connect to mail.webspeed.online directly.

Duplicate sent messages — some clients save to Sent while the server also does. Turn off one of the two in the client settings.

Next

  • imap
  • smtp
  • pop
  • webmail
  • outlook
  • thunderbird
  • apple mail
  • port 993

Ready to use this

Mailboxes on your own domain with webmail and IMAP.

  • MX, SPF, DKIM and DMARC published for you
  • Daily sending caps that protect delivery
See email plans
Still stuck? Open a ticket from Support tickets in the console, or email [email protected]. Include the service name, the exact error and what you already tried.